VISIT US:
1630 W. MISSION ROAD
ESCONDIDO, CA 92029
​
TAKE NORDAHL RD EXIT OFF HWY 78
CALL US:
SE HABLA ESPAÑOL
IF IT'S METAL, WE'VE GOT IT!
CUTTING & OTHER SERVICES
PLEASE NOTE - WE CHARGE FOR ALL CUTTING SERVICES. PLEASE SEE THE SPECIFIC PRICES IN THE SECTIONS BELOW.
CHOPSAW CUTTING
SHEAR CUTTING
BANDSAW CUTTING
MAXIMUM CUTTING SIZE IS 6" X 6"
STRAIGHT CUTS ONLY - NO ANGLE CUTS
NO PRECISION CUTS! - TOLERANCE IS +/- 1/4"
DUE TO BLADE THICKNESS, YOU WILL LOSE 1/4" OF MATERIAL ON EACH CUT
​​
-
UP TO 3" - $2.00 PER CUT
-
3" TO 5" - $4.00 PER CUT
-
5+" TO 6" - $5.00 PER CUT
STACKED CUTS ARE $1.00 FOR EACH ADDITIONAL ITEM
ALL STACKED CUTS MUST BE THE SAME LENGTH & FIT IN THE CUTTING AREA. AND CAN NOT BE LARGER THAN 1ST CUT ITEM.
-
EXAMPLE - 2 STACKED CUTS ON $2.00 CUT = $2+$1+$1 - $4.00
​
​
GALVANIZING
CUSTOM GALVANIZING
WE CAN SEND JUST ABOUT ANY HOT ROLLED STEEL TO A LOCAL SOUTHERN CALIFORNIA PROCESSER
​
TURN AROUND TIME IS APPROXIMATELY 10 DAYS TO 2 WEEKS. QUICKER OPTIONS MAY BE AVAILABLE AT A HIGHER PRICE IF NEEDED
​
COST IS BASED ON SIZE AND WEIGHT OF THE MATERIAL TO BE DIPPED. OUR SALES TEAM CAN GIVE YOU A QUOTE FOR COST
​
WE ALSO STOCK ONE OF THE LARGEST GALVANIZED STEEL INVENTORIES IN THE REGION INCLUDING TUBE, PIPE, FLAT BAR, ANGLE, AND CHANNEL!
​
​
ALL CUTS ARE COMPLETED WITH A WATER-BASED LUBRICANT - SOME RUSTING MAY OCCUR AFTER CUTS ARE COMPLETED
MAXIMUM CUTTING SIZE IS 16" WIDE X 10" TALL
STRAIGHT CUTS ONLY - NO ANGLE CUTS
NO PRECISION CUTS! - TOLERANCE IS +/- 1/8" - WE CAN NOT GUARANTEE PERFECT SQUARENESS OF MATERIAL
DUE TO BLADE THICKNESS, YOU COULD LOSE UP TO 1/8" OF MATERIAL ON EACH CUT
​​
$20.00 PER CUT - INCLUDES ALL STACKED MATERIAL
1/2 HOUR CUTTING - $40.00
1 HOUR CUTTING - $80.00
​
DUE TO TYPE AND THICKNESS OF MATERIAL, TIME CHARGE MAY SUPERSEDE SINGLE CUT CHARGE
​
​
​
MAXIMUM CUTTING IS 1/2" THICK
48" X 120" - HOT ROLLED STEEL ONLY
MINIMUM THICKNESS IS 26 GUAGE
70" WIDE
MAXIMUM CUTTING - STAINLESS STEEL
DEPENDS ON HARDNESS - CONTACT STAFF FOR MORE INFORMATION
​
STRAIGHT CUTS ONLY - NO ANGLE CUTS
NO PRECISION CUTS!
TOLERANCE IS +/- 1/8"
​
1ST SHEAR CUT - $20.00
2ND CUT OR 1/2 HOUR CUTTING - $40.00
1 HR CUTTING - $80.00
​
METAL FABRICATION - WATER JETTING POWDER COATING
UNFORTUNATLY, WE ARE NOT A FABRICATION SHOP
WE ONLY PROVIDE ROUGH CUT-TO-SIZE SERVICES AS MENTIONED ABOVE
HOWEVER, WE CAN WORK WITH YOU TO HELP FIND FABRICATION COMPANIES AND OPTIONS THAT CAN HELP YOU GET YOUR JOB ACROSS THE FINISH LINE!
​
JUST ASK FOR INFORMATION FROM ONE OF OUR WAREHOUSE ASSOICIATES OR OUR SALES TEAM
​
​
TRACK BURN &
TORCH CUTS
DO YOU NEED PLATE STEEL THICKER THAN 1/2" CUT? WE ARE ABLE TO TRACK BURN UP TO 2" THICK STEEL IN-HOUSE!
​
STRAIGHT CUTS ONLY - NO ANGLE CUTS
​
NO PRECISION CUTS - TOLERANCE IS +/- 1/4" OR GRATER DEPENDING ON MATERIAL & THICKNESS
​
DUT TO CUTTING TECHNIQUE, YOU WILL LOSE 1/4" OR GRATER OF MATERIAL WITH EACH CUT
​
PRICING IS BASED ON THICKNESS OF THE MATERIAL & IS PRICED BY THE INCH BEING CUT. SETUP TIME WILL BE INCLUDED IN THE PRICE AS THERE ARE MANY MORE STEPS REQUIRED FOR CUTTING OF THIS KIND
​
FOR LARGE MATERIAL SUCH AS PIPE AND I-BEAMS LARGER THAN OUR BANDSAW CAN ACCOMMODATE, ROUGH TORCH CUTTING IS AVAILABLE. PRICE IS QUOTED BY THE SIZE AND TIME REQUIRED FOR THE CUT
​
INSTALLATION
WE DO NOT OFFER ANY INSTALLATION OR DESIGN SERVICES
HOWEVER, WE CAN SUGGEST LOCAL FABRICATORS AND INSTALLERS BASED ON YOUR NEED AND THEIR SPECIALIES THAT CAN HELP TO MAKE YOUR VISION COME TRUE!
​
JUST ASK FOR FOR INFORMATION FROM ONE OF OUR SALES TEAM
​
​